Microchip PIC18F2410

PIC18F2410 概要

DEVICE OVERVIEWThis document contains device specific information for the following devices:  • PIC18F2410     • PIC18LF2410  • PIC18F2510     • PIC18LF2510  • PIC18F2515     • PIC18LF2515  • PIC18F2610     • PIC18LF2610  • PIC18F4410     • PIC18LF4410  • PIC18F4510     • PIC18LF4510  • PIC18F4515     • PIC18LF4515  • PIC18F4610     • PIC18LF4610This family offers the advantages of all PIC18 microcontrollers – namely, high computational performance at an economical price – with the addition of high-endurance, Flash program memory. On top of these features, the PIC18F2X1X/4X1X family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power sensitive applications.Power-Managed Modes:• Run: CPU On, Peripherals On• Idle: CPU Off, Peripherals On• Sleep: CPU Off, Peripherals Off• Idle mode Currents Down to 3.0 μA Typical• Sleep mode Currents Down to 20 nA Typical• Timer1 Oscillator: 1.8 μA, 32 kHz, 2V• Watchdog Timer: 2.1 μA• Two-Speed Oscillator Start-upPeripheral Highlights:• High-Current Sink/Source 25 mA/25 mA• Up to 2 Capture/Compare/PWM (CCP) modules, One with Auto-Shutdown (28-pin devices)• Enhanced Capture/Compare/PWM (ECCP) module (40/44-pin devices only):   - One, two or four PWM outputs   - Selectable polarity   - Programmable dead time   - Auto-shutdown and auto-restart• Master Synchronous Serial Port (MSSP) module Supporting 3-Wire SPI (all 4 modes) and I2C™ Master and Slave modes• Enhanced Addressable USART module:   - Supports RS-485, RS-232 and LIN 1.2   - RS-232 operation using internal oscillator block (no external crystal required)   - Auto-wake-up on Start bit   - Auto-Baud Detect• 10-Bit, Up to 13-Channel Analog-to-Digital Converter module (A/D):   - Auto-acquisition capability   - Conversion available during Sleep• Dual Analog Comparators with Input Multiplexing• Programmable 16-Level High/Low-Voltage Detection (HLVD) module:   - Supports interrupt on High/Low-Voltage Detection  Flexible Oscillator Structure:• Four Crystal modes, Up to 40 MHz• 4x Phase Lock Loop (PLL) – Available for Crystal and Internal Oscillators• Two External RC modes, Up to 4 MHz• Two External Clock modes, Up to 40 MHz• Internal Oscillator Block:   - 8 user-selectable frequencies, from 31 kHz to 8 MHz   - Provides a complete range of clock speeds from 31 kHz to 32 MHz when used with PLL   - User-tunable to compensate for frequency drift• Secondary Oscillator using Timer1 @ 32 kHz• Fail-Safe Clock Monitor:   - Allows for safe shutdown if peripheral clock stopsSpecial Microcontroller Features:• C Compiler Optimized Architecture:   - Optional extended instruction set designed to optimize re-entrant code• 100,000 Erase/Write Cycle Flash Program Memory Typical• Three Programmable External Interrupts• Four Input Change Interrupts• Priority Levels for Interrupts• 8 x 8 Single-Cycle Hardware Multiplier• Extended Watchdog Timer (WDT):   - Programmable period from 4 ms to 131s• Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via Two Pins• In-Circuit Debug (ICD) via Two Pins• Wide Operating Voltage Range: 2.0V to 5.5V• Programmable Brown-out Reset (BOR) with Software Enable Option

特徴

• Up to 10 MIPS performance
• C compiler optimized RISC architecture
• 8 x 8 Single Cycle Hardware Multiply
• Internal oscillator support 31 kHz to 8 MHz
• Fail-Safe Clock Monitor – allows safe shutdown if clock fails
• Watchdog Timer with separate RC oscillator
• Wide operating Voltage range; 2.0V to 5.5V
• Run, Idle and Sleep modes
• Idle mode currents down to 5.8uA typical
• Sleep mode currents down to 0.1uA typical
• 10-bit ADC, 10 channels, 100K samples per second
• Programmable Low Voltage Detection Module
• Programmable Brown-out Reset module
• Two Analog comparators with input multiplexing
• Master Synchronous Serial Port supports SPI ™ and I2C™ Master and Slave Mode
• EUSART module including LIN bus support
• Four Timer Modules
• Up to 2 PWM outputs
• Up to 2 Capture / Compare

仕様