Microchip DSPIC33FJ32MC304T-E/ML

DSPIC33FJ32MC304T-E/ML 概要

The dsPIC33F16-bit device family employs a powerful 16-bit architecture, idealfor applications that rely on high-speed, repetitive computations, as wellas control. The devices are pin compatible with the PIC24HJ family ofdevices, and share a very high degree of compatibility with the dsPIC30Ffamily devices. This allows seamless migration options from/to PIC24F,dsPIC30F and dsPIC33F devices.

特徴

• Operating Conditions:
• 3.0V to 3.6V, -40ºC to +150ºC, DC to 20 MIPS
• 3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
• High-Performance DSC CPU:
• Modified Harvard architecture
• C compiler optimized instruction set
• 16-bit wide data path
• 24-bit wide instructions
• Linear program memory addressing up to 4M instruction words
• Linear data memory addressing up to 64 Kbytes
• 83 base instructions: mostly 1 word/1 cycle
• Two 40-bit accumulators with rounding and saturation options
• Flexible and powerful addressing modes: Indirect, Modulo and Bit-Reversed Software stack
• 16 x 16 fractional/integer multiply operations
• 32/16 and 16/16 divide operations
• Single-cycle multiply and accumulate: Accumulator write back for DSP operations and Dual data fetch
• Up to ±16-bit shifts for up to 40-bit data
• On-Chip Flash and SRAM:
• Flash program memory
• Data SRAM
• Boot, Secure, and General Security for program Flash
• Direct Memory Access (DMA):
• 8-channel hardware DMA
• Up to 2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA
• Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)
• Most peripherals support DMA
• Timers/Capture/Compare/PWM:
• Timer/Counters, up to five 16-bit timers: Can pair up to make two 32-bit timers
• One timer runs as a Real-Time Clock with an external 32.768 kHz oscillator and Programmable prescaler
• Input Capture (up to four channels): Capture on up, down or both edges
• 16-bit capture input functions and 4-deep FIFO on each capture
• Output Compare (up to four channels): Single or Dual 16-bit Compare modeand 16-bit Glitchless PWM mode
• Hardware Real-Time Clock/Calendar (RTCC): Provides clock, calendar, and alarm functions
• Interrupt Controller:
• 5-cycle latency
• 118 interrupt vectors
• Up to 53 available interrupt sources
• Up to three external interrupts
• Seven programmable priority levels
• Five processor exceptions
• Digital I/O:
• Peripheral pin Select functionality
• Up to 35 programmable digital I/O pins
• Wake-up/Interrupt-on-Change for up to 21 pins
• Output pins can drive from 3.0V to 3.6V
• Up to 5V output with open drain configuration
• All digital input pins are 5V tolerant
• 4 mA sink on all I/O pins
• System Management:
• Flexible clock options: External, crystal, resonator, internal RC, Fully integrated Phase-Locked Loop (PLL) and Extremely low jitter PLL
• Power-up Timer
• Oscillator Start-up Timer/Stabilizer
• Watchdog Timer with its own RC oscillator
• Fail-Safe Clock Monitor
• Reset by multiple sources
• Power Management:
• On-chip 2.5V voltage regulator
• Switch between clock sources in real time
• Idle, Sleep, and Doze modes with fast wake-up
• Analog-to-Digital Converters (ADCs):
• 10-bit ADC, 1.1 Msps or 12-bit, 500 Ksps conversion: two and four simultaneous samples
• Up to nine input channels with auto-scanning
• Conversion start can be manual or synchronized with one of four trigger sources and possible in Sleep mode
• Comparator Module:
• Two analog comparators with programmable input/output configuration
• CMOS Flash Technology:
• Low-power, high-speed Flash technology
• Fully static design
• 3.3V (±10%) operating voltage
• Industrial and Extended temperature
• Low power consumption
• Motor Control Peripherals:
• 6-channel 16-bit Motor Control PWM: three duty cycle generators
• Independent or complementary mode and programmable dead time and output polarity
• Edge-aligned or center-aligned, manual output override control, and one Fault input
• Trigger for ADC conversions
• PWM frequency for 16-bit resolution (@ 40>
• PWM frequency for 11-bit resolution (@ 40>
• 2-channel 16-bit Motor Control PWM
• One duty cycle generator, Independent or Complementary mode and programmable dead time and output polarity
• Edge-aligned or center-aligned, manual output override control and one fault input
• Trigger for ADC conversions
• PWM frequency for 16-bit resolution (@ 40>
• PWM frequency for 11-bit resolution (@ 40>
• 2-Quadrature Encoder Interface modules
• Phase A, Phase B, and index pulse input and 16-bit up/down position counter

仕様